PLANET EARTH

Norton Waterstone Starter Kit: 220/1000 grit stone, 4000/8000 grit stone, SiC flattening stone $129.00 Waterstone starter sharpening kit includes 2 sharpening stones for edge repair and final finish work, flattening stone, and instructional DVD….

Norton IM200 -8 Three Stone Sharpening System – Fine India, Medium Crystolon, and Coarse Crystolon stones $80.53 This system was designed not only to produce an excellent edge on your fine cutlery, but also to preserve it, by removing only enough metal to give an extremely sharp edge. Whether your knives are just a little dull, or whether they are knicked and battered or previously sharpened improperly, these whetstones will deliver a perfectly honed, sharp edge. Professional and home chefs will find it easy…

Norton Flattening Stone for Waterstones, 3/4 x 3 x 9 in plastic case $24.95 The softness of a waterstone allows it to quickly develop a fast cutting abrasive slurry. Thats a real plus for honing, but a negative when you start to develop shallow indentations and irregularities in the surface. Nortons flattening stone, when rubbed across your waterstones surface, quickly flattens and refreshes the face. Its coarse grit silicon carbide promotes maximum cutting while the diag…

Norton Masonry Depressed Center Abrasive Wheel, Type 27, Silicon Carbide, 5/8 Arbor, 4 Diameter x 1/4 Thickness (Pack of 10) $21.43 One of China’s biggest stars…. Long out of print Hong Kong CD….

3M Wetordry 9088NA Sandpaper, 9-Inch x 11-Inch, 5-Sheet, Assorted-Grit $2.50 The standard for Wet-or-Dry sandpaper, this paper utilizes a silicon carbide abrasive bonded with a waterproof resin to an improved paper backing, resulting in an improved rate of cut, increased abrasive life, increased flexibility, and a uniform, consistent finish. Uses include sanding new surfaces, burnishing old finishes, and feathering fine edges. Grit : Assortment # of sheets : 59″ x 11″….

Silicon Carbide Sharpening Stone $27.95 Silicon Carbide Sharpening StoneModel Number: 99-100…

Foamex UltraSOLV Silicon Carbide ScrubPADs $44.00 Patented scrubbing tools for use in PM procedures on process equipment in semiconductor, flat panel display, optical componenet and hard disk drive industries. Allows for safe and efficient scrubbing of the most difficult to clean process chambers….

Silicon Carbide Sharp Stone $20.49 Silicon Carbide Sharp StoneOur instruments are manufactured within the guidelines of the FDA quality assurance system for Good Manufacturing Practices and our factory is ISO 13485 certified. All our products bear the CE mark,emblematic of the European Community’s highest standards….

Brake Rotor Flex-Hone Brake, Flywheel Surface Finish Tool 240 Grit (Silicon Carbide) $34.99 …

1 (25mm) Flex-Hone Cylinder Hone Tool 320 Grit (Silicon Carbide) $19.99 The Flex-Hone® tool is a surface refinishing tool that will is used to refinish and restore cylinder bores. The surface finish is dependant on the grit used. The tool is used for applications like engine rebuilding, hydraulic cylinders, brake rebuilding and general machining operations. Flex-Hone® Tool can be used with honing oil or engine oil. If honing hydraulic cylinders use the intended hydr…

1.25 0.15 HP Submersible Dewatering Pump – Float Switch: Ball Type Built-In Float Switch with 33′ Cord $319.99 BJM1000: The Silver Bullet Pump (R-Series) submersible pump from BJM is ideal for dewatering construction sites, mines or for all around use in industrial plants and utilities. The R100 has features normally only offered with larger, more expensive, pumps. The motor is protected by a heavy duty mechanical seal made of silicon carbide. Rotor shaft, motor housing and all hardware is made of 304 stainless steel and all other wet parts are made of reinforced plastic. A thermal breaker ensures shut-down should overheating occur. The R100 is an ideal pump for many different applications, and can be used in salt water. Features: -Optional Float Switch with choice of 33′ or 50′ cord -Light dewatering -1.25 Top discharge -3/4 Garden hose adapter -304 Stainless steel motor housing -Salt water compatible Specifications: -115 Volts -0.15 HP -Rated Amps: 2 -Discharge Size: 1.25 -Max Head: 20′ -Max GPM: 24 -Cable: 33′ -Weight: 9 lbs

1.25 0.15 HP Submersible Dewatering Pump – Float Switch: Ball Type Built-In Float Switch with 50′ Cord $349.99 BJM1000: The Silver Bullet Pump (R-Series) submersible pump from BJM is ideal for dewatering construction sites, mines or for all around use in industrial plants and utilities. The R100 has features normally only offered with larger, more expensive, pumps. The motor is protected by a heavy duty mechanical seal made of silicon carbide. Rotor shaft, motor housing and all hardware is made of 304 stainless steel and all other wet parts are made of reinforced plastic. A thermal breaker ensures shut-down should overheating occur. The R100 is an ideal pump for many different applications, and can be used in salt water. Features: -Optional Float Switch with choice of 33′ or 50′ cord -Light dewatering -1.25 Top discharge -3/4 Garden hose adapter -304 Stainless steel motor housing -Salt water compatible Specifications: -115 Volts -0.15 HP -Rated Amps: 2 -Discharge Size: 1.25 -Max Head: 20′ -Max GPM: 24 -Cable: 33′ -Weight: 9 lbs

1.25 0.15 HP Submersible Dewatering Pump – Float Switch: No $159.99 BJM1000: The Silver Bullet Pump (R-Series) submersible pump from BJM is ideal for dewatering construction sites, mines or for all around use in industrial plants and utilities. The R100 has features normally only offered with larger, more expensive, pumps. The motor is protected by a heavy duty mechanical seal made of silicon carbide. Rotor shaft, motor housing and all hardware is made of 304 stainless steel and all other wet parts are made of reinforced plastic. A thermal breaker ensures shut-down should overheating occur. The R100 is an ideal pump for many different applications, and can be used in salt water. Features: -Optional Float Switch with choice of 33′ or 50′ cord -Light dewatering -1.25 Top discharge -3/4 Garden hose adapter -304 Stainless steel motor housing -Salt water compatible Specifications: -115 Volts -0.15 HP -Rated Amps: 2 -Discharge Size: 1.25 -Max Head: 20′ -Max GPM: 24 -Cable: 33′ -Weight: 9 lbs

1.5 , 5.5 HP Honda Engine Driven High Pressure Pump $884.49 TSU1017: This Tsurumi pump is specifically made for high pressure output most fully utilized for irrigation, spraying, or sprinkling.Capable of multiple discharge lines combined with power and durability this water pump is unique yet affordable. Features: -Heavy-duty Honda gas engine with oil sensor and Silicon Carbide mechanical seal provides the longest life in this class -Maximum pressure of 100 PSI appropriate for high pressure applications; sprinkling, fire-fighting, irrigation, water transfer to long/high distances, etc. -Versatile 3-way discharge coupling allows pump to run up to three discharge lines simultaneously. Two 1 couplings and one 1 1 2 coupling -High head, closed impeller and cast iron volute casing deliver high performance and long wear life. Specifications: -Max Capacity: 106 GPM -Max Head 231′ -Tank Size: 0.95 -5.5 HP Warranty Tsurumi’s limited 2 year warranty. Warranty evaluations will be done within 2 days after receipt by Tsurumi’s Authorized Repair Center.

1.5 IPT Electric Submersible Pump with 1/3 HP Motor $358.99 OTS1187: This slim, lightweight CSA listed IPT pump features top discharge as well as thermal overload protection. Fully equipped with cast iron impellers, 304 stainless steel casing, motor housing, shaft and hardware, this IPT Submersible Pump can move up to 50 gallons of water per minute. With a 30-foot power cable, this pump can be placed almost anywhere it’s needed. For optimum results, add the optional Piggyback Mercury-Free Float Switch. The mercury-free liquid level control has a piggyback plug molded into the cord, allowing the submersible pump motor to plug into the cord, and then plug the entire assembly into a standard grounded outlet. This reliable, cost effective, low maintenance IPT Submersible Pump is designed to work with non-flammable liquids which are compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST Features: -Silicon carbide Viton lubricated lower seal -Carbon ceramic Viton lubricated upper seal -Nitrile O-rings -Overload/thermal breaker Specifications: -Motor HP: 1/3 -Motor Voltage: 115V -Overall Height: 14.5 -Diameter: 6.66 -Discharge Port Size: 1.5 NPT -Max Head: 32 ft. -Delivers Up To: 13.8 PSI -Max Water Flow: 50 GPM -Suction Strainer: 0.39 x0.29 slots on 0.31 staggered centers -Minimum Liquid Height: 3 -CSA Listed Piggyback Float Switch Standard Features: -30-foot 115V/13 Amp cord -Mercury-free -No wiring -Adjustable clamp -Corrosion resistant -Proven reliability -Omni directional -Variable pumping range -Easily installed

1.5 IPT Electric Submersible Pump with 1/3 HP Motor $359.99 OTS1185: This slim, lightweight CSA listed IPT pump features top discharge as well as thermal overload protection. Fully equipped with cast iron impellers, 304 stainless steel casing, motor housing, shaft and hardware, this IPT Submersible Pump can move up to 50 gallons of water per minute. With a 30-foot power cable, this pump can be placed almost anywhere it’s needed. For optimum results, add the optional Piggyback Mercury-Free Float Switch. The mercury-free liquid level control has a piggyback plug molded into the cord, allowing the submersible pump motor to plug into the cord, and then plug the entire assembly into a standard grounded outlet. This reliable, cost effective, low maintenance IPT Submersible Pump is designed to work with non-flammable liquids which are compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST Features: -Silicon carbide Viton lubricated lower seal -Carbon ceramic Viton lubricated upper seal -Nitrile O-rings -Overload/thermal breaker Specifications: -Motor HP: 1/3 -Motor Voltage: 115V -Overall Height: 14.5 -Diameter: 6.66 -Discharge Port Size: 1.5 NPT -Max Head: 32 ft. -Delivers Up To: 13.8 PSI -Max Water Flow: 50 GPM -Suction Strainer: 0.39 x0.29 slots on 0.31 staggered centers -Minimum Liquid Height: 3 -CSA Listed

100GRIT DRYWL SANDG SCREEN $4.01 Reversible, non-clogging, open mesh, precut for quick and easy attachment to FibaTape vacuum drywall sander, impregnated with extra sharp, silicon carbide abrasive for fast and easy work. Coarse 100-grit for trouble-free first coat sanding, fine 150-gritfor extra-smooth final finishing. Rinse with cold water for reuse.

110 Piece Super Accessory Kit 709-01 $21.56 OEO1139: Features: -Accessory kit .-Versatile and reusable accessory kit includes everything you need to cut, grind, sand, polish, drill, sharpen and clean .-Includes #540 1-1/4 cut off wheel, #428 3/4 carbon steel brush, #421 polishing compound, four #429 1 felt polishing wheel, #83142 silicon carbide grinding stone, #191 high speed cutter, #407 1/2 60 grit sanding drum with mandrel, #430 1/4 60 .-grit sanding band with mandrel, #402 mandrel, #90962 wrench, #953 aluminum oxide grinding stone, #84922 silicon carbide grinding stone, #952 aluminum oxide grinding stone, twelve #409 15/16 emery cut off wheel, twelve #420 15/16 heavy duty emery .-cut off wheel, #426 1-1/4 fiberglass reinforced cut off wheel, four #414 small felt wheel, #422 cone polishing tip, six #408 1/2 60 grit sanding band, twelve #411 3/4 180 grit sanding disc, twelve #412 3/4 220 grit sanding disc, twelve #413 3/4 .-240 grit sanding disc, six #431 1/4 60 grit sanding band, six #432 1/2 120 grit sanding band, six #438 1/4 120 grit sanding band, #401 mandrel, #415 dressing stone, #405 bristle brush and #511E 180 grit abrasive buff .-110 pieces .-Carded .

12 Cylinder Silicon Carbide Abrasive Polishing Tools 1 $34.5 12 Cylinder Silicon Carbide Abrasives For Polishing Gold & Semi Pecious Alloys. This is a new set of 12 cylinder silicon carbide abrasives. Great for polishing gold and semi precious alloys. These have a coarse grit. Each measures approximately 1 x 1/2 (25 x 13 mm).

120c Wetddry Sandpaper $24.85 Use to sand between coats of finishes Use with water to reduce clogging Features silicon carbide For sanding metal for repainting or primer 9 x 11 sheets 25 sheets per pack Size: GRIT:120C

1500a Wetodry Sandpapr $23.77 Use to sand between coats of finishes Use with water to reduce clogging Features silicon carbide For sanding metal for repainting or primer 9 x 11 sheets 25 sheets per pack Size: GRIT:1500A

150GRIT DRYWL SANDG SCREEN $4.01 Reversible, non-clogging, open mesh, precut for quick and easy attachment to FibaTape vacuum drywall sander, impregnated with extra sharp, silicon carbide abrasive for fast and easy work. Coarse 100-grit for trouble-free first coat sanding, fine 150-gritfor extra-smooth final finishing. Rinse with cold water for reuse.

150c Wetodry Sandpaper $21.92 Use to sand between coats of finishes Use with water to reduce clogging Features silicon carbide For sanding metal for repainting or primer 9 x 11 sheets 25 sheets per pack Size: GRIT:150C

15299 FLORPAPR 8X50YD 2/0 100 per 50 YD $145.58 Coating of silicone carbide grams bonded to flexible backing. 8 x 50 yd. 100-2/0 grit.. Silicon carbide Closed coating Width: 8” x 50 Yd. Size: GRIT:100-2/0

2 , 4 HP Honda Engine Driven Centrifugal Pump with Low Oil Sensor $523.19 TSU1008: Combining the power of a Honda engine and the durability that has come to personify Tsurumi pumps, this water pump is ideal for any situation. Both lightweight and powerful it can be used in almost environment and provides an affordable and efficient solution to excess water problems. Features: -Heavy-duty Honda gas engine with oil sensor and Silicon Carbide mechanical seal provides the longest life in this class -Cast Iron impeller and volute casing last long and guarantee low maintenance -Durable Rolled-Steel frame provides pump/engine with maximum protection, perfect ease of handling or transport, and safe operation Specifications: -Max Capacity: 137 GPM -Max Head: 115′ -Tank Size:.66 -4 HP Warranty Tsurumi’s limited 2 year warranty. Warranty evaluations will be done within 2 days after receipt by Tsurumi’s Authorized Repair Center.

2 , 4.5 HP Robin Engine Driven Centrifugal Pump with Low Oil Sensor $477.19 TSU1007: This gas powered Robin Subaru engine water pump combines both heavy duty performance with a light weight frame. It’s not only an effective pump in almost any situation but is affordable as well. Made with durable and reliable materials this pump is perfect for almost any situation. Features: -Heavy-duty Robin gas engine with oil sensor and Silicon Carbide mechanical seal provides the longest life in this class -Cast Iron impeller and volute casing last long and guarantee low maintenance -Durable Rolled-Steel frame provides pump/engine with maximum protection, perfect ease of handling or transport, and safe operation Specifications: -Max Capacity: 137 GPM -Max Head: 115′ -Tank Size:.95 -4.5 HP Warranty Tsurumi’s limited 2 year warranty. Warranty evaluations will be done within 2 days after receipt by Tsurumi’s Authorized Repair Center.

2 , 5.5 HP Honda Engine Driven Trash Pump with Low Oil Sensor $1176.09 TSU1013: This Honda driven trash pump provides both the power and durability necessary to handle almost any situation. With strong and innovative design and materials this water pump provides a reliable solution to your excess liquids.Both lighweight as well as affordable this Tsurami pump is an excellent pick. Features: -Heavy-duty Honda gas engine with oil sensor deliver high power from a compact, reliable design. Silicon Carbide mechanical seal provides the longest life in this class. -High Chrome impeller, Cast Iron volute casing plus Stainless Steel wear plate promise increased durability and decreased maintenance -Pump/engine set mounted to cage frame on Rubber Vibration Cushions to buffer stress and wear. -Durable Rolled-Steel frame provides pump/engine with maximum protection, perfect ease of handling or transport, and safe operation -Galvanized Steel hose couplings promise longer thread life Specifications: -Max Capacity: 190 GPM -Max Head 90′ -Tank Size: .95 -5.5 HP Warranty Tsurumi’s limited 2 year warranty. Warranty evaluations will be done within 2 days after receipt by Tsurumi’s Authorized Repair Center.

2 , 6 HP Robin Engine Driven Trash Pump with Low Oil Sensor $944.89 EPT3-80RX pictured, actual size may vary from picture – TSU1012: This water pump provides both the heavy duty durability with the highest degree of performance. An emphasis on the strongest materials allows for the maximum output with minimum maintenance. Capable of cleaning up almost any mess and at an affordable price, this Tsurumi pump is both effective and affordable. Features: -Heavy-duty Robin gas engine with oil sensor deliver high power from a compact, reliable design. Silicon Carbide mechanical seal provides the longest life in this class. -High Chrome impeller, Cast Iron volute casing plus Stainless Steel wear plate promise increased durability and decreased maintenance -Pump/engine set mounted to cage frame on Rubber Vibration Cushions to buffer stress and wear. -Durable Rolled-Steel frame provides pump/engine with maximum protection, perfect ease of handling or transport, and safe operation -Galvanized Steel hose couplings promise longer thread life Specifications: -Max Capacity: 190 GPM -Max Head 90′ -Tank Size: .95 -6 HP Warranty Tsurumi’s limited 2 year warranty. Warranty evaluations will be done within 2 days after receipt by Tsurumi’s Authorized Repair Center.

2 – 3 Semi-Trash Pump with Honda Engine – Model: SEH-50T – 2 NPT, 158 GPM $692 KOS1004: These Semi Trash Pumps by Koshin come with powerful OHV Honda engines with low oil sensors. These Koshin models come equipped with silicon carbide mechanical seals, which help with increased abrasive resistance, longer life and less maintenance for you. As well as the impeller and volute being manufactured from Spherodial Graphite cast iron for longer life and less maintenance for you. These Koshin Semi-Trash Pump with Honda Engines have light weight die cast aluminum casing and a full roll cage that protects the pump and engine with vibration isolator. Lastly these models come with strainer and wrench standard. Features: -Honda Engine with low oil sensor -Silicon carbide mechanical seals -Pump casings that are die cast aluminum -Spherodial Graphite cast iron Impellers and Volutes -Vibration isolators built into the full steel roll cage -Strainer and wrench Applications: -Those iffy pumping situations -General dewatering -Pumping high abrasive and solids Specifications: -Suction Discharge Size: -SEH-50T: 2 NPT -SEH-80T: 3 NPT -Maximum Capacity: -SEH-50T:158 GPM -SEH-80T: 238 GPM -Maximum Head: -SEH-50T: 95′ -SEH-80T: 85′ -Maximum Suction Lift: 26′ -Maximum Pressure: -SEH-50T: 41.1 PSI -SEH-80T: 36.8 PSI -Engine Type: -SEH-50T: Honda GX 120 -SEH-80T: Honda GX 160 -Displacement: -SEH-50T: 118 cc -SEH-80T: 163 cc -Horse Power: -SEH-50T: 4.0 HP -SEH-80T: 5.5 HP -Fuel Tank Capacity: -SEH-50T: .66 Gal -SEH-80T: .95 Gal -Continuous Operation Time Per Tank: 2.5 HRS -Fuel: Automobile non-lead gasoline – Weight: -SEH-50T: 56 lbs -SEH-80T: 75 lbs -Dimensions: -SEH-50T: 15 H x 14 W x 18 D -SEH-80T: 17 H x 15 W x 20 D SEH-50T/SEH80T_Semi-Trash_Pump-Specification_Sheet

2 Cast Iron Dewatering Pump with 6.5 HP Briggs and Stratton Engine – Seal: Buna-N Silicon Carbide $564.99 OTS1004: This AMT industrial duty dewatering pump offers economy, durability, portability, and performance in one package. Built with rugged, long lasting cast iron construction, this pump features a dual volute design that reduces radial load on the engine. Also features an ever-ready 6.5 HP Briggs Stratton engine, as well as check valves that ensure constant self-priming up to 20 ft. This AMT Dewatering Pump is ideal for agricultural applications, irrigation, spraying, washdown, and general dewatering. Same day shipping for phone orders placed before 2 pm EST Features: -Dual volute design -Two NPT pipe nipples -Optional Buna-N or Viton Mechanical Seal -Stainless steel shaft sleeve -Built in flapper/check valve -Fiber gasket casing seal -Semi-open, clog resistant impellers -Carry-handle and heavy-duty steel base Specifications: -Engine Model: Briggs Stratton CP650 -Engine HP: 6.5 -Solids Handling: 3/8 -Max Working Pressure: 60 PSI -Delivers Up To: 52 PSI -Max Water Flow: 140 GPM (8,400 GPH) @ 3,600 RPM -Self-priming up to: 20 ft. -Max Temperature: 180 F -Seal: Buna-N Silicon Carbide or Viton -Run-Time: 90 min. -Tank Size: 3 qt. -Weight: 76 lbs.

2 Cast Iron Dewatering Pump with 6.5 HP Briggs and Stratton Engine – Seal: Viton $609.99 OTS1004: This AMT industrial duty dewatering pump offers economy, durability, portability, and performance in one package. Built with rugged, long lasting cast iron construction, this pump features a dual volute design that reduces radial load on the engine. Also features an ever-ready 6.5 HP Briggs Stratton engine, as well as check valves that ensure constant self-priming up to 20 ft. This AMT Dewatering Pump is ideal for agricultural applications, irrigation, spraying, washdown, and general dewatering. Same day shipping for phone orders placed before 2 pm EST Features: -Dual volute design -Two NPT pipe nipples -Optional Buna-N or Viton Mechanical Seal -Stainless steel shaft sleeve -Built in flapper/check valve -Fiber gasket casing seal -Semi-open, clog resistant impellers -Carry-handle and heavy-duty steel base Specifications: -Engine Model: Briggs Stratton CP650 -Engine HP: 6.5 -Solids Handling: 3/8 -Max Working Pressure: 60 PSI -Delivers Up To: 52 PSI -Max Water Flow: 140 GPM (8,400 GPH) @ 3,600 RPM -Self-priming up to: 20 ft. -Max Temperature: 180 F -Seal: Buna-N Silicon Carbide or Viton -Run-Time: 90 min. -Tank Size: 3 qt. -Weight: 76 lbs.

2 Cast Iron Solids Handling Pump with 6.5 HP Briggs and Stratton Engine Kit $728.99 OTS1229: The AMT line of Solids Handling Pumps offers upgraded debris handling capability in wear resistant cast iron construction. Perfect for high volume liquid transfer, irrigation, commercial draining and construction. Able to pass solids up to 3/8 in diameter, this self-priming pump is highly portable, and comes stock with a 6.5 HP Briggs Stratton engine. This pump is designed for use with nonflammable liquids compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST (Orders placed with Factory Installed Seal Options are subject to longer ship times) Features: -Semi-open, clog resistant cast iron impeller -Two 2 NPT pipe nipples -Buna mechanical seal -Self primes up to 20 feet -Stainless steel shaft sleeve -Wear resistant cast iron replaceable volute/wearplate and impeller -Built in flapper/check valve -Solids handling capability Specifications: -Engine Model: Briggs Stratton CP650 -Engine HP: 6.5 -Solids Handling: 3/8 -Port Size: 2 NPT -Max Head: 120 ft. -Delivers Up To: 52 PSI -Max Water Flow: 150 GPM @ 3,600 RPM -Self Primes Up To: 20 ft. -Max Temperature: 180 F -Seal: Buna -Run-Time: 90 min. -Tank Size: 3.0 qt. -Weight: 82 lbs. Customize This Pump With: 10 Semi-Pneumatic/16 Pneumatic Wheel Kits These wheel kits enable you to move your pump with ease. Designed for all AMT water pumps with roll frames, these Wheel Kits can have you working more efficiently, and cut job times in half. Kits include everything you need to have your pump fully mobile in no time. Be sure to specify between 10 semi-pneumatic, or 16 pneumatic wheels. Specifications: -10 semi-pneumatic wheels, or -16 pneumatic wheels Deluxe Factory Installed Seal Options for Solids Handling Pumps w/ Viton Seal, Flapper, and Gasket Customize your AMT Solids Handling Pump with a factory installed seal of your preference. Installation Includes: -Silicon Carbide/Viton Seal -Flapper -Gasket Factory Installed Seal Options for Solids Handling P

2 Cast Iron Submersible Contractor Pump w/ Chromium Impellers and 2.0 HP Motor $1546.99 OTS1224: This high quality AMT Submersible Pump is designed for residential, commercial, and industrial settings. Highly versatile, this pump can adequately perform on construction sites, for waste water, storm water, farming, irrigation, excavation, mining, marine, basement and other general drainage applications involving sediment laden liquids with solids up to 3/8 in diameter. Featuring rugged high-chromium steel impellers, this pump can withstand a beating and still outperform the competition for years to come. This 2.0 HP Submersible Contractor Pump with single phase motor can move up to 135 gallons of water per minute, and is designed for use with non-flammable liquids compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST Features: -Superior motor design for quiet, low noise operation -Silicon carbide mechanical seals plus shaft seal -UL/CSA Listed -Stainless steel motor housing -32′ cord (no plug) -Suction screen -Carrying handle -High Chromium, clog resistant impeller and cover Specifications -HP: 2.0 -Port NPT: 2 -Construction: Cast Iron -Max Head: 73 ft. -Max PSI: 31.6 -Max GPM: 135 -Type: Contractor Sumbersible -Volts AC @ 60Hz: 230 -Full Load Amps: 10.9 -Max Temperature: 104 Degrees F

2 Dredging Pump with 4.7 HP Yanmar Diesel Engine $2942.99 OTS1010: This industrial duty dredging pump is designed to pump seawater and freshwater containing up to 25% sand, debris, and other abrasive particles. It can be used for many marine applications, such as dredging, pile driving, pier maintenance, emergency bilging, and wash down. This heavy-duty pump is powered by a rugged Yanmar Diesel engine, and with its high chromium stainless steel construction, will last over 500 hours of service (with regular maintenance and rinsing of pump after every use.) Incredibly reliable, cost effective, and low maintenance. Same day shipping for phone orders placed before 2 pm EST Features: -High chromium stainless steel internal components resist wear from abrasive materials -Heavy-duty roll cage -Silicon Carbide/Buna-N mechanical seal resists abrasives and extends seal life -Dual volute design -Heavy-duty cast iron casing and adapter for durability in even the most extreme conditions -O-Ring casing seal for easy service and cleaning -Two NPT pipe nipples and suction strainer Specifications: -Engine Model: Yanmar Diesel L48 -Engine HP: 4.7 -Solids Handling: 1/2 -Max Working Pressure: 75 PSI -Max Head: 101 ft. @ Sea Water (42 PSI) -Max Water Flow: 173 GPM @ 3,600 RPM -Self-priming up to: 10 ft. in 1 minute; 20 ft. maximum -Max Temperature: 160 F -Seal: Silicon Carbide w/ Buna-N -Run-Time: 110 min. -Tank Size: 2.6 qt. -Weight: 95 lbs. This pump is compatible with the the 10 Semi-Pneumatic Wheel Kit, and the 16 Pneumatic Wheel Kit: our skus ots1021 and ots1022, respectively

2 IPT Electric Submersible Pump with 1/2 HP Motor $421.99 OTS1188: This slim, lightweight CSA listed IPT pump features top discharge as well as thermal overload protection. Fully equipped with cast iron impellers, 304 stainless steel casing, motor housing, shaft and hardware, this IPT Submersible Pump can move up to 65 gallons of water per minute. With a 30-foot power cable, this pump can be placed almost anywhere it’s needed. For optimum results, add the optional Piggyback Mercury-Free Float Switch. The mercury-free liquid level control has a piggyback plug molded into the cord, allowing the submersible pump motor to plug into the cord, and then plug the entire assembly into a standard grounded outlet. This reliable, cost effective, low maintenance IPT Submersible Pump is designed to work with non-flammable liquids which are compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST Features: -Silicon carbide Viton lubricated lower seal -Carbon ceramic Viton lubricated upper seal -Nitrile O-rings -Overload/thermal breaker Specifications: -Motor HP: 1/2 -Motor Voltage: 115V -Overall Height: 14.5 -Diameter: 6.66 -Discharge Port Size: 2 NPT -Max Head: 40 ft. -Delivers Up To: 17.3 PSI -Max Water Flow: 65 GPM -Suction Strainer: 0.39 x 0.29 slots on 0.31 staggered centers -Minimum Liquid Height: 3 -CSA Listed

3 , 5.5 HP Honda Engine Driven Centrifugal Pump with Low Oil Sensor $630.69 TSU1010: Combining the power of a Honda engine with the durability of Tsurumi parts, this water pump is both reliable and affordable.A heavy duty water pump at a light weight, it utilizes high quality materials to provide a toughness allowing for increased versatility. This Tsurumi pump is ideal for almost any scenario pertaining to water problems and can suit all your needs. Features: -Heavy-duty Honda gas engine with oil sensor and Silicon Carbide mechanical seal provides the longest life in this class -Cast Iron impeller and volute casing last long and guarantee low maintenance -Durable Rolled-Steel frame provides pump/engine with maximum protection, perfect ease of handling or transport, and safe operation Specifications: -Max Capacity: 137 GPM -Max Head: 115′ -Tank Size:.95 -5.5 HP Warranty Tsurumi’s limited 2 year warranty. Warranty evaluations will be done within 2 days after receipt by Tsurumi’s Authorized Repair Center.

3 , 6 HP Robin Engine Driven Centrifugal Pump with Low Oil Sensor $524.49 TSU1009: Robin engine driven water pump that provides power and reliability for any excess water situation. With durable and reliable materials, allows for wear and tear with minimum maintenance. This pump is both high powered and high quality serving as an affordable solution to any pesky water problem. Features: -Heavy-duty Robin gas engine with oil sensor and Silicon Carbide mechanical seal provides the longest life in this class -Cast Iron impeller and volute casing last long and guarantee low maintenance -Durable Rolled-Steel frame provides pump/engine with maximum protection, perfect ease of handling or transport, and safe operation Specifications: -Max Capacity: 264 GPM -Max Head: 105′ -Tank Size:.95 -6 HP Warranty Tsurumi’s limited 2 year warranty. Warranty evaluations will be done within 2 days after receipt by Tsurumi’s Authorized Repair Center.

3 , 8 HP Honda Engine Driven Trash Pump with Low Oil Sensor $1561.99 TSU1015: Whether it be at a construction site or in a commercial setting this water pump provides both the power and durability to get the job done.This Tsurumi pump combines both reliability thanks to its quality parts and performance with the help of the Honda engine. Features: -Heavy-duty Honda gas engine with oil sensor deliver high power from a compact, reliable design. Silicon Carbide mechanical seal provides the longest life in this class. -High Chrome impeller, Cast Iron volute casing plus Stainless Steel wear plate promise increased durability and decreased maintenance -Pump/engine set mounted to cage frame on Rubber Vibration Cushions to buffer stress and wear. -Durable Rolled-Steel frame provides pump/engine with maximum protection, perfect ease of handling or transport, and safe operation -Galvanized Steel hose couplings promise longer thread life Specifications: -Max Capacity: 360 GPM -Max Head 96′ -Tank Size: 1.6 -8 HP Warranty Tsurumi’s limited 2 year warranty. Warranty evaluations will be done within 2 days after receipt by Tsurumi’s Authorized Repair Center.

3 AMT Premium Trash Pump with 8.0 HP Briggs and Stratton Engine $1550.99 OTS1062: The AMT line of Premium Trash pumps feature additional cleanout covers for the heaviest debris applications. This pump is constructed of durable cast aluminum components featuring removeable/replaceable cast iron volutes, impellers, and wearplates. Simple cleanout design permits easy removal of trash and debris without disconnecting hoses. This pump is powered by a rugged 8.0 HP Briggs Stratton 1350 Series engine with Oil Alert, and can handle solids up to 1.5 in diameter while pumping up to 340 gallons of water per minute. This durable AMT trash pump is designed to work with non-flammable liquids which are compatible with pump component materials. Features: -Additional cleanout covers -Two 3 NPT pipe nipples -Viton/Silicon carbide mechanical seal -Stainless steel shaft sleeve -Steel suction strainer -Rugged steel roll frame Specifications: -Engine Model: Briggs STratton 1350 Series with Oil Alert -Engine HP: 8.0 -Max Solids Handling: 1.5 -Port Size: 3 -Max Head: 100 ft. -Delivers Up To: 42 PSI -Max Water Flow: 340 GPM @ 3,600 RPM -Self Primes Up To: 20 ft. -Max Temperature: 180 F -Seal: Viton -O-Ring Casing Seal: Buna-N -Run-Time: 90 min. -Tank Size: 4.0 qt. -Weight: 151 lbs. This pump is compatible with the the 10 Semi-Pneumatic Wheel Kit, and the 16 Pneumatic Wheel Kit: our skus ots1021 and ots1022, respectively

3 AMT Premium Trash Pump with 9.0 HP Honda OHV Engine $1851.99 OTS1063: The AMT line of Premium Trash pumps feature additional cleanout covers for the heaviest debris applications. This pump is constructed of durable cast aluminum components featuring removeable/replaceable cast iron volutes, impellers, and wearplates. Simple cleanout design permits easy removal of trash and debris without disconnecting hoses. This pump is powered by a rugged 9.0 HP Honda OHV engine with Oil Alert, and can handle solids up to 1.5 in diameter while pumping up to 340 gallons of water per minute. This durable AMT trash pump is designed to work with non-flammable liquids which are compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST Features: -Additional cleanout covers -Two 3 NPT pipe nipples -Viton/Silicon carbide mechanical seal -Stainless steel shaft sleeve -Steel suction strainer -Rugged steel roll frame Specifications: -Engine Model: Honda GX270 OHV with Oil Alert -Engine HP: 9.0 -Max Solids Handling: 1.5 -Port Size: 3 -Max Head: 100 ft. -Delivers Up To: 42 PSI -Max Water Flow: 340 GPM @ 3,600 RPM -Self Primes Up To: 20 ft. -Max Temperature: 180 F -Seal: Viton -O-Ring Casing Seal: Buna-N -Run-Time: 100 min. -Tank Size: 6.4 qt. -Weight: 169 lbs. This pump is compatible with the the 10 Semi-Pneumatic Wheel Kit, and the 16 Pneumatic Wheel Kit: our skus ots1021 and ots1022, respectively

3 AMT Premium Trash Pump with Electric Start 10.0 HP Yanmar Diesel Engine $4584.99 OTS1065: The AMT line of Premium Trash pumps feature additional cleanout covers for the heaviest debris applications. This pump is constructed of durable cast aluminum components featuring removeable/replaceable cast iron volutes, impellers, and wearplates. Simple cleanout design permits easy removal of trash and debris without disconnecting hoses. This pump is powered by an Electric Start-10.0 HP Yanmar Diesel engine, and can handle solids up to 1.5 in diameter while pumping up to 340 gallons of water per minute. This durable AMT trash pump is designed to work with non-flammable liquids which are compatible with pump component materials. Features: -12 VDC Electric Start (battery not included) -Additional cleanout covers -Two 3 NPT pipe nipples -Viton/Silicon carbide mechanical seal -Stainless steel shaft sleeve -Steel suction strainer -Rugged steel roll frame Specifications: -Engine Model: Yanmar Diesel L100 with Electric Start -Engine HP: 10.0 -Max Solids Handling: 1.5 -Port Size: 3 -Max Head: 100 ft. -Delivers Up To: 42 PSI -Max Water Flow: 340 GPM @ 3,600 RPM -Self Primes Up To: 20 ft. -Max Temperature: 180 F -Seal: Viton -O-Ring Casing Seal: Buna-N -Run-Time: 100 min. -Tank Size: 6.0 qt. -Weight: 205 lbs. This pump is compatible with the the 10 Semi-Pneumatic Wheel Kit, and the 16 Pneumatic Wheel Kit: our skus ots1021 and ots1022, respectively

3 AMT Trash Pump with 9.0 HP Honda OHV Engine $1807.99 OTS1059: The AMT line of Engine Driven Trash pumps are designed for applications which require high flow efficiency and solids handling capability. This pump is constructed of durable cast aluminum components featuring removeable/replaceable cast iron volutes, impellers, and wearplates. Simple cleanout design permits easy removal of trash and debris without disconnecting hoses. This pump is powered by a rugged 9.0 HP Honda OHV engine with Oil Alert, and can handle solids up to 1.5 in diameter while pumping up to 300 gallons of water per minute. This durable AMT trash pump is designed to work with non-flammable liquids which are compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST Features: -Two 3 NPT pipe nipples -Viton/Silicon carbide mechanical seal -Stainless steel shaft sleeve -Steel suction strainer -Rugged steel roll frame Specifications: -Engine Model: Honda GX270 OHV with Oil Alert -Engine HP: 9.0 -Max Solids Handling: 1.5 -Port Size: 3 -Max Head: 85 ft. -Delivers Up To: 37 PSI -Max Water Flow: 300 GPM @ 3,600 RPM -Self Primes Up To: 20 ft. -Max Temperature: 180 F -Seal: Viton -O-Ring Casing Seal: Buna-N -Run-Time: 100 min. -Tank Size: 6.4 qt. -Weight: 158 lbs. This pump is compatible with the the 10 Semi-Pneumatic Wheel Kit, and the 16 Pneumatic Wheel Kit: our skus ots1021 and ots1022, respectively

3 Cast Iron Submersible Contractor Pump w/ Chromium Impellers and 3.0 HP Motor $1737.99 OTS1225: This high quality AMT Submersible Pump is designed for residential, commercial, and industrial settings. Highly versatile, this pump can adequately perform on construction sites, for waste water, storm water, farming, irrigation, excavation, mining, marine, basement and other general drainage applications involving sediment laden liquids with solids up to 3/8 in diameter. Featuring rugged high-chromium steel impellers, this pump can withstand a beating and still outperform the competition for years to come. This 3.0 HP Submersible Contractor Pump with single phase motor can move up to 220 gallons of water per minute, and is designed for use with non-flammable liquids compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST Features: -Superior motor design for quiet, low noise operation -Silicon carbide mechanical seals plus shaft seal -UL/CSA Listed -Stainless steel motor housing -32′ cord (no plug) -Suction screen -Carrying handle -High Chromium, clog resistant impeller and cover Specifications -HP: 3.0 -Port NPT: 3 -Construction: Cast Iron -Max Head: 68 ft. -Max PSI: 29.4 -Max GPM: 220 -Type: Contractor Sumbersible -Volts AC @ 60Hz: 230 -Full Load Amps: 17.2 -Max Temperature: 104 Degrees F

3 Cast Iron Submersible Contractor Pump w/ Chromium Impellers and 5.0 HP Motor – Float Switch: None $2146.99 OTS1226: This high quality AMT Submersible Pump is designed for residential, commercial, and industrial settings. Highly versatile, this pump can adequately perform on construction sites, for waste water, storm water, farming, irrigation, excavation, mining, marine, basement and other general drainage applications involving sediment laden liquids with solids up to 3/8 in diameter. Featuring rugged high-chromium steel impellers, this pump can withstand a beating and still outperform the competition for years to come. This 5.0 HP Submersible Contractor Pump with three-phase motor can move up to 240 gallons of water per minute, and is designed for use with non-flammable liquids compatible with pump component materials. Same day shipping for phone orders placed before 2 pm EST Features: -Superior motor design for quiet, low noise operation -Silicon carbide mechanical seals plus shaft seal -UL/CSA Listed -Stainless steel motor housing -32′ cord (no plug) -Suction screen -Carrying handle -High Chromium, clog resistant impeller and cover Specifications -HP: 5.0 -Port NPT: 3 -Construction: Cast Iron -Max Head: 88 ft. -Max PSI: 38 -Max GPM: 240 -Type: Contractor Sumbersible -Volts AC @ 60Hz: 230 -Full Load Amps: 13.9 -Max Temperature: 104 Degrees F

3 GR Trash Pump with 6.7 HP Yanmar Diesel Engine $4554.99 OTS1078: The Gorman-Rupp line of Engine Driven Trash Pumps is designed for applications which require high flow efficiency and solids handling capability. This pump is constructed of durable cast aluminum components featuring removeable/replaceable ductile cast iron impellers, and wearplates. Simple cleanout design permits easy removal of trash and debris without disconnecting hoses. This pump is powered by a rugged 6.7 HP Yanmar Diesel engine, and can handle solids up to 1.5 in diameter while pumping up to 390 gallons of water per minute. This durable Gorman-Rupp trash pump is designed to work with non-flammable liquids which are compatible with pump component materials. Features: -Two 3 NPT suction/discharge pipe nipples -Viton/Silicon carbide mechanical seal -90-Degree discharge elbow -Steel suction strainer -Rugged steel roll frame Specifications: -Engine Model: Yanmar L70 Diesel -Engine HP: 6.7 -Max Solids Handling: 1.5 -Port Size: 3 -Max Head: 85 ft. -Delivers Up To: 36 PSI -Max Water Flow: 390 GPM @ 3,300 RPM -Self Primes Up To: 25 ft. -Max Temperature: 180 F -Seal: Viton -Run-Time: 2.2 hrs. -Tank Size: 0.92 gal. -Weight: 124 lbs. This pump is compatible with the 10 Semi-Pneumatic Wheel Kit, our sku: ots1080

3 GR Trash Pump with Electric Start 6.7 HP Yanmar Diesel Engine $5331.99 OTS1079: The Gorman-Rupp line of Engine Driven Trash Pumps is designed for applications which require high flow efficiency and solids handling capability. This pump is constructed of durable cast aluminum components featuring removeable/replaceable ductile cast iron impellers, and wearplates. Simple cleanout design permits easy removal of trash and debris without disconnecting hoses. This pump is powered by an Electric Start 6.7 HP Yanmar Diesel engine, and can handle solids up to 1.5 in diameter while pumping up to 390 gallons of water per minute. This durable Gorman-Rupp trash pump is designed to work with non-flammable liquids which are compatible with pump component materials. Features: -Electric Start (battery not included) -Two 3 NPT suction/discharge pipe nipples -Viton/Silicon carbide mechanical seal -90-Degree discharge elbow -Steel suction strainer -Rugged steel roll frame Specifications: -Engine Model: Yanmar L70 Diesel -Engine HP: 6.7 -Max Solids Handling: 1.5 -Port Size: 3 -Max Head: 85 ft. -Delivers Up To: 36 PSI -Max Water Flow: 390 GPM @ 3,300 RPM -Self Primes Up To: 25 ft. -Max Temperature: 180 F -Seal: Viton -Run-Time: 2.2 hrs. -Tank Size: 0.92 gal. -Weight: 124 lbs. This pump is compatible with the 10 Semi-Pneumatic Wheel Kit, our sku: ots1080

3-5/16X11 CRSE SANDPAPER 5PK $3.34 Extra sharp, silicon carbide abrasive on precut backing designed for quick, easy attachment to FibaTape hand or pole sanders (not FibaTape vacuum sander). Easily cuts through drywall compound for fast work. Coarse 80-grit for fast first coat sanding, fine120-grit for finer, smoother finish coat.

3-in-1 Tool and Knife Sharpening System Benchstone Stations – im100 6x2x1/2 three in one tool and knif $138.99 OLP1721: This item features: -Designed for general sharpening, is a mini version of the Multi-Oilstone containing coarse Crystolon, medium Crystolon, and fine India stones. -Designed to produce the finest edges possible, contains fine India, Soft Arkansas, and Hard Arkansas stones. -Width: 2 in. -Height: 1/2 in. -Length: 6 in. -Applicable Materials: Most Metals, Hard Steel. -Includes: Instructions, 4 oz. Oil. -Quantity: 5 per pack. Model Code #160; #160;Model Description AARoughness Grade:Coarse, Medium, Fine, Abrasive Material:Silicon Carbide/Regular Alumina, Abrasive Trade Name:Crystolon/India ABRoughness Grade:Fine, Extra Fine, Ultra Fine

3M (MMM2021) 3M Imperial Wetordry 5-1/2 x 9 Sheet – 50 Sheets per Sleeve $0.01 TM3679: Features and Benefits: -Levels orange peel, dust nibs or paint runs in refinish acrylic lacquer paint. -3Ms fastest cutting, longest lasting abrasive for saving labor costs and improving quality. -Abrasive mineral type: silicon carbide. -ANSI grade: 1000. Suggested hand sanding pad: MMM05530 -3M Imperial Wetordry 5-1/2 x 9 Sheet – 50 Sheets per Sleeve.-New out of box defects 30d warranty .

3M 051144994229 99422na 220a Wetodry Sandpaper $18.61 For producing rich satin-smooth finishes of professional quality on lacquer, varnish, enamel and synthetic coatings. Silicon carbide mineral abrasive. 9” x 11” sheets. No. 99419NA: 600A grit No. 99420NA: 400A grit No. 99421NA: 320A grit No. 99422NA: 220A grit

3M 88580 9 x 11 120g tri-m-ite $0.67 3M Pro-Pak Tri-M-ite Fre-Cut non-loading, dry sanding sandpaper features silicon carbide, a sharp synthetic mineral that cuts fast and smooth. Use it to sand between coats of paint, varnish or other finishes.

3M 88624 9 x 11 180g tri-m-ite $0.5 3M Pro-Pak Tri-M-ite Fre-Cut non-loading, dry sanding sandpaper features silicon carbide, a sharp synthetic mineral that cuts fast and smooth. Use it to sand between coats of paint, varnish or other finishes.

3M 9088NA Silicon Carbide WetorDry Abrasive Sheets $3.32 3M 9088NA Silicon Carbide WetorDry Abrasive Sheets

3M 99425 9 x 11 220g tri-m-ite $0.5 3M Pro-Pak Tri-M-ite Fre-Cut non-loading, dry sanding sandpaper features silicon carbide, a sharp synthetic mineral that cuts fast and smooth. Use it to sand between coats of paint, varnish or other finishes.

3M 99427 9 x 11 150g tri-m-ite $0.76 3M Pro-Pak Tri-M-ite Fre-Cut non-loading, dry sanding sandpaper features silicon carbide, a sharp synthetic mineral that cuts fast and smooth. Use it to sand between coats of paint, varnish or other finishes.

3M 99429 9 x 11 100g tri-m-ite $0.76 3M Pro-Pak Tri-M-ite Fre-Cut non-loading, dry sanding sandpaper features silicon carbide, a sharp synthetic mineral that cuts fast and smooth. Use it to sand between coats of paint, varnish or other finishes.

3M Automotive Products 3M 2022 Imperial Wetordry Sandpaper P1200 Grit- 5.5quot;x9quot;- 50 Sheets $0.01 TM3678: Features and Benefits: -Levels orange peel, dust nibs or paint runs in all types of paints and is appropriate for light sanding on refinish lacquer. -3Ms fastest cutting, longest lasting abrasive for saving labor costs and improving quality. -Abrasive mineral type: silicon carbide. -ANSI grade: 1200. Suggested hand sanding pad: MMM05530 -3M Imperial Wetordry 5-1/2 x 9 Sheet – 50 Sheets per Sleeve.-New out of box defects 30d warranty .

3M Company #10455 9×11 VF 220G Sandpaper $101.48 Fabricut, 9 x 11 , Very Fine 220 Grit, Waterproof Silicon Carbide, Sanding Screen Wet Or Dry, Used For Old Finish Removal, Bulk Sleeve.

3M Company #10456 9x11Fine 180G Sandpaper $68.79 Fabricut, 9 x 11 , Fine 180 Grit, Waterproof Silicon Carbide, Sanding Screen, Wet Or Dry, Used For Old Finish Removal, Bulk Sleeve.

3M Company #20908-150 150G Spon Block $0.01 SandBlaster sanding sponges offer up to 3 times longer life and cuts up to 3 times faster than traditional sponges. 3-3/4” x 2-5/8” x 1” thick. Color coded packaging for type of sanding job. 36 and 60 grit sponges coated in silicon carbide. 80 thru 320 grit sponges made of aluminum oxide abrasive on 4 sides of urethane foam sponge for sanding contoured and hard-to-reach surfaces. Rinse clean and use again. For applications ranging from paint removal to final finish sanding. No. 20909-36: Extra coarse, 36 grit No. 20909-60: Coarse, 60 grit No. 20908-80: Medium, 80 grit No. 20908-100: Medium, 100 grit No. 20908-150: Medium, 150 grit No. 20907-180: Fine, 180 grit No. 20907-320: Extra fine, 320 grit

Tags: silicon carbide, silicon carbide grit, silicon carbide powder, silicon carbide properties, silicon carbide sandpaper

This entry was posted on Saturday, January 7th, 2012 at 10:30 am and is filed under Rocks. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.